Lastolite E Photomaker Web Kit: Small Product Photos at Home
By Borge's Imaging — Shop Photography, Printing and Studio Gear in Melbourne Borge's Imaging | Published: 2026-11-04
Category: How-to Guides
Set up the Lastolite E Photomaker Web Kit for clean white-background product photos at home. Follow these steps to light, shoot and avoid common mistakes.
Quick answer
Set up the Lastolite E Photomaker Web Kit on a stable table, position your product on the white background, light it evenly from the front, and shoot slightly above product level. Check your first frame for shadows and colour cast before shooting the full set.
Why a tabletop kit beats a makeshift setup
A dedicated kit like the Lastolite E Photomaker Web Kit gives you a consistent white background and a repeatable lighting position. That consistency matters more than raw power for small products: buyers compare your images side by side, and uneven backgrounds or shifting shadows make a catalogue look amateur. The kit collapses for storage, so you can keep a permanent shooting spot without dedicating a room to it.
The trade-off is scale. This kit is built for small to medium items, not furniture or full outfits. If your products are larger than the background area, you will see edges and falloff, and no amount of editing will fix a subject that does not fit.
Where the kit fits and where it does not
Use the kit for jewellery, cosmetics, small electronics, packaged goods, accessories and similar items that fit comfortably on a tabletop. It is also a sensible choice for ecommerce product shots on a budget because you avoid renting studio time for every new SKU.
Skip it for anything reflective or transparent that needs precise reflection control, and for products that require multiple lighting angles. Those cases need more modifiers than a single kit provides. Also check that your camera or phone can focus close enough; the kit does not change your lens's minimum focus distance.
Step-by-step: Lastolite E Photomaker Web Kit setup
- Set up on a stable, level table: Choose a table that does not wobble and place the kit away from windows that change light during the shoot. Open the kit and position the white background so it curves smoothly from floor to back wall. Checkpoint: press the background flat and confirm there are no creases visible in the viewfinder before you place the product.
- Position the product with breathing room: Place the item slightly forward of the back curve, leaving visible white space around it. For tall items, angle the camera down slightly rather than pushing the product into the curve. Common mistake: placing the product too close to the back edge, which creates a hard shadow line and makes the item look cramped.
- Light evenly from the front: Aim the kit's light source at the product from the front and slightly above. Move it closer for softer shadows or further for more contrast. Keep the light centred so both sides of the product receive similar brightness. Checkpoint: take one test frame and look for a bright hotspot on the product; if present, move the light back or diffuse it.
- Set camera height and framing: Place the camera at or slightly above the product's midpoint, not looking down steeply. Fill about 70–80% of the frame with the product and leave even margins. Use a tripod or steady support if your shutter speed is low. Common mistake: shooting from standing height, which flattens the product and shows the top instead of the front.
- Check white balance and exposure: Set white balance manually or use a grey card under the same lighting. Adjust exposure so the white background is bright but not clipped; check the histogram if your camera shows one. Checkpoint: the background should read as white, not grey or blue, and the product should keep visible detail in its brightest areas.
- Shoot a consistent set: Keep the camera and light positions fixed and move only the product between shots. Capture front, side and detail views for each item, then review the set together before packing up. Common mistake: adjusting the light between products, which makes the final images look like they came from different shoots.
Product facts
- Lastolite E Photomaker Web product Kit: Collapsible for easy storage You can pack it away between shoots, so a home setup does not need permanent space.
Lastolite E Photomaker Web product Kit - Lastolite E Photomaker Web product Kit: Enables a clean white background to subject A consistent white background reduces editing work and keeps product listings visually uniform.
- Lastolite E Photomaker Web product Kit: Ideal for selling products on the web The kit is designed around the kind of small-item shots most online listings need.
