Why the 320M needs a different approach than a fixed stand
The Kupo 320M Roller Stand with Castor Wheels is designed to move, not to stay put. That mobility is its advantage in a busy studio, but it also means your usual fixed-stand habits need adjusting. A stand that rolls can shift if you forget the brakes, and its footprint and load capacity set hard limits on what you can safely mount.
This guide covers the practical checks that matter most: matching your load to the 12 kg maximum, planning the floor space around the 105.92 cm footprint, using the braked castors correctly, and deciding whether the 320M suits your boom or heavy-light setup.
The 320M numbers that drive your positioning decisions
- Kupo 320M Roller Stand with Castor Wheels: Maximum Load 12 kg This is the ceiling for everything you mount, including the fixture, modifier and any grip accessories. Weigh your complete load before rolling the stand into position.

Kupo 320M Roller Stand with Castor Wheels - Kupo 320M Roller Stand with Castor Wheels: Footprint Diameter 105.92 cm The castor base needs roughly a metre of clear floor. Check this against doorways, cable runs and trip hazards before you commit to a spot.
- Kupo 320M Roller Stand with Castor Wheels: Weight 7.57 kg The stand itself is substantial. Factor that into lifting and transport, especially when moving it between locations.
- Kupo 320M Roller Stand with Castor Wheels: Minimum Extension Height 114.3 cm, Maximum Extension Height 270 cm The working height range tells you whether the stand fits your intended light position and ceiling clearance.
Positioning checks before you roll the stand into place
- Clear the floor area: The 105.92 cm footprint diameter means the castors need a clear circle of floor. Remove loose cables, stands and cases from that zone so the wheels can move without catching.
- Plan the roll path: Decide your route before loading the stand. The 320M weighs 7.57 kg empty, so a loaded stand is harder to steer around tight corners and door thresholds.
- Check height clearance: At full extension the stand reaches 270 cm. Confirm ceiling height, overhead rigging and doorway clearance along your path before raising it.
- Confirm the mount: The 320M uses a fixed Baby 5/8 in (16 mm) stud. Check that your fixture or grip head accepts that interface before you plan the position.
Using the braked castors as a safety tool
The built-in braked caster wheels are the 320M's main safety feature, but they only help if you use them deliberately. Lock the brakes once the stand is in position, especially on smooth studio floors where a light nudge can send an unbraked stand rolling.
When repositioning, release the brakes, move the stand slowly and reapply them before you walk away. Avoid rolling a loaded stand over cables or uneven surfaces, where a castor can catch and tip the load. The supplied information does not specify brake type or wheel material, so test the brakes on your actual floor before trusting them with a heavy fixture.
What the 320M does not give you: levelling and spring cushioning
Two features are explicitly absent from the 320M record: it has no levelling leg and no spring cushioning. That matters on uneven floors, ramps or outdoor locations, where a non-levelling stand may sit with one castor unloaded. Choose a flat, level surface, or use wedges or shims under the castors if the floor is slightly uneven.
Without spring cushioning, the stand does not absorb the shock of a dropped or suddenly lowered load. Lower fixtures gently and avoid letting a heavy light drop onto the stand.
Roller stand or boom base? Match the 320M to the job
Kupo describes the 320M as a great alternative to a full-sized roller stand and a perfect complement to a boom setup. That makes it a good fit for supporting lights, monitors or booms in the studio or on location, provided your total load stays within 12 kg.
If your boom and counterweight combination exceeds that limit, or if you need a levelling leg for uneven ground, the 320M is not the right base. The supplied record does not list a levelling accessory or a higher-capacity variant, so confirm your options before ordering.
Kupo 320M at a glance
- Kupo 320M Roller Stand with Castor Wheels: Risers 2, Sections 3 Fewer sections than a taller stand means quicker height changes, but check the maximum 270 cm suits your lighting plan.
- Kupo 320M Roller Stand with Castor Wheels: Closed Length 114.05 cm This is the length you need to fit in a vehicle or storage cupboard when the stand is collapsed.
- Kupo 320M Roller Stand with Castor Wheels: Fixed Stand Adapter Baby 5/8 in (16 mm) Stud The fixed stud accepts standard Baby receivers. Confirm your fixture or grip head uses that mount.
Moving a loaded 320M safely
- Reduce the load first: Remove the fixture or modifier before moving the stand any distance. A 12 kg load at height makes the stand top-heavy and harder to control.
- Lower before you roll: Collapse the risers to bring the centre of gravity down. The 320M has no spring cushioning, so lower the load gently rather than letting it drop.
- Push, don't pull: Push the stand from the column rather than pulling it by the fixture or cable. This keeps the castors tracking and reduces tipping risk.
- Re-brake and re-check: Once in the new position, lock the brakes and confirm the stand is stable before reattaching the load.
What to confirm before you buy
The supplied record confirms the 320M's load limit, height range, footprint, mount and weight, but it does not include assembly instructions, brake specifications or guidance on uneven floors. If you need a stand for sloped or uneven locations, or for loads approaching 12 kg at full height, check those details with the store before ordering.
For most studio work where the floor is flat and the load is well within 12 kg, the 320M's braked castors and 270 cm reach make it a practical choice for lights, monitors and boom support.

